009 Civic 2 AND 4-Door Aluminum Wheel Instructions

Clean the mating surface and the valve hole of the aluminum wheel.
Install the tire pressure sensor and the washer to the aluminum wheel, and loosely install the valve nut. Make sure the pressure sensor is resting on the wheel.
NOTE: Install the tire pressure sensor so that the sensor housing surface should not exceed the wheel protrusion to prevent the sensor housing caught to the bead of the tire when assembled the tire.
Tighten the valve nut to the specified torque while holding the tire pressure sensor toward the wheel.
Tightening torque: 4 N·m (0.4 kgf·m, 3 lbf·ft)
Install the tires according to the instructions in the Service Manual.
Install the wheels on the vehicle and torque to 108 N·m (80 lbf-ft).
Manual 2009 Civic 2 AND 4-Door Aluminum Wheel Instructions Guide. Make your sport car more different and look cool by use this accessories. In this pdf book, you will know how to install with the right way.
Open the driver’s door. Using isopropyl alcohol, clean the area where the accessory tire pressure caution label will attach. Remove the backing from the label and attach it over the existing tire information label. Attach the tire pressure caution label or label C or label D according to the following information:
Label: For EX-L Model with a T125/70D15 95M

Label C: For EX-L Model with a T135/80R16 101M
Label D: For EX-L Model with a T135/80D16 101M
Attach the “Supplemental Information” page included in this kit to the Owner’s Manual. For the method of attaching the page, refer to “To the dealer:” attached to the “Supplemental Information” page.
MEMORIZING THE TIRE PRESSURE SENSOR ID
Using the HDS and Snap-on TPMS sensor initializer tool, memorize the ID of tire pressure sensor ID according to the instructions in the Service Manual (Memorizing the Tire Pressure Sensor ID).
We found pdf this automotive pdf file from google search engine, and can be found from the original site at here www.hondapartsnow.com. We provide you direct
download from original site here Manual 2009 Civic 2 AND 4-Door Aluminum Wheel Instructions Guide.pdf. We hope this online pdf book will useful for you.

Read more →

2006 and up Honda Civic Si TWM Performance Shift Boot Installation Manual

2006 and up Honda Civic Si TWM Performance Shift Boot Installation Manual.2006 and up Honda Civic Si TWM Performance Shift Boot Installation Manual. Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the shift boot on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working. Pull the emergency brake up to prevent the car from moving while you work. Looking down at the shift knob, turn the jam nut beneath the shift knob clockwise using a 14 mm wrench to loosen it.Remove the staples holding the shift boot to the plastic ring. A small flat head screwdriver or needle nose pliers can be used to pry the staples out. Use the wire cutters or scissors to cut off the extra length of zip tie. In order to ensure a smooth surface on the zip tie that will not damage the inside of the shift boot, trim it as pictured to the lower left. Cut the tie wrap so that the wire cutters remove a corner of the tie wrap head as well, instead of just trimming the excess length. This ensures a very smooth surface free of sharp edges as there will be no protruding tie wrap if it is cut in this manner. Now turn the shift boot right side out to prepare to mount it to the plastic base. Install the TWM shift boot on to the plastic base without removing the backing from the double-sided tape yet. The sewn flaps on either side of the shift boot should line up with the indentations on either side of the plastic base. In addition, the rectangular notches along the bottom of the TWM shift boot should line up with the 4 tabs that extend from the bottom of the plastic base as pictured to the left. If these do not line up, remove the boot and rotate it 180 degrees to line up the grooves and rectangular notches with the tabs.

Download: 2006 and up Honda Civic Si TWM Performance Shift Boot Installation Manual

Read more →